Field note · Flexo prepress

PDF/X for flexo packaging: PDF/X-1a vs PDF/X-4

What PDF/X is, how PDF/X-1a, PDF/X-4, and PDF/X-6 differ, the Ghent Workgroup flexo checks for text size, line width, ink coverage, and overprint, how dielines and white travel as processing-step layers, and what to log at file intake.

Plate area · jobs · customers · AR — one system of record
Flexoworks
  • flexo
  • prepress
  • packaging
  • artwork
  • preflight
  • pdf

PDF/X is a family of ISO standards (ISO 15930) that restricts PDF to what a print workflow can reproduce predictably. A PDF/X file carries its fonts, images, and an output intent that names the print condition it was built for, and it leaves out anything that could print differently on another system. For a flexo trade shop, the version on the incoming file decides who flattened the transparency, which color spaces can appear, and whether dielines and white can travel as layers. Most "wrong file" arguments at intake come down to those three things.

The PDF/X versions you will see

Version Standard Color allowed Transparency and layers Where it shows up in flexo
PDF/X-1a ISO 15930-1:2001 and later revision CMYK, gray, spot only No. Flattened at export Legacy RIPs, older brand templates
PDF/X-3 2002 and later revision Adds RGB, Lab, and ICC-based color No Rarely requested for packaging
PDF/X-4 and X-4p ISO 15930-7:2010 As X-3, with a required embedded (X-4) or external (X-4p) output profile Yes, live Basis of the Ghent Workgroup packaging specs
PDF/X-5n ISO 15930, 2008 and later n-colorant output intents Yes Extended color gamut and spot inks used as process
PDF/X-6 ISO 15930-9:2020 As X-4, on PDF 2.0 Yes Not yet in production use

The PDF Association describes PDF/X-1a as the most restrictive member: a file must print "without requiring prior color correction," so only CMYK, gray, and spot colors are allowed. PDF/X-4 is based on PDF 1.6 and was the first part to permit transparency, adding layers, 16-bit images, JPEG2000, and OpenType fonts. PDF/X-6 moves to PDF 2.0 with page-level output intents and CxF/X-4 spot color data (PDF Association), but the Ghent Workgroup left it out of its 2022 specs because "the hardware and software in our market isn't ready for that yet" (GWG).

Rules every PDF/X file follows

The PDF Association's key facts list the requirements common to all parts:

  • An output intent with an ICC profile for the intended print condition. This is the press profile the CMYK values were separated for.
  • All fonts embedded, all images inside the file, no low-resolution alternates.
  • Every spot color has an alternate color, and the same one everywhere it is used.
  • No passwords, transfer curves, LZW compression, JavaScript, form fields, embedded files, or annotations in the print area.
  • If a BleedBox is defined, it sits outside the TrimBox.
  • Metadata states whether the file has been trapped and which PDF/X part it claims.

PDF/X deliberately does not set image resolution or bleed size, because those depend on the print condition. For packaging, the Ghent Workgroup fills that gap.

PDF/X-1a vs PDF/X-4 for flexo

The practical difference is where flattening happens. A PDF/X-1a export flattens every drop shadow, opacity, and blend mode in the designer's application with the designer's settings. A PDF/X-4 file keeps transparency live, so the prepress RIP flattens it with settings that match the press. The FTA's FIRST 7 design guide warns that effects look right on screen but "final output requires flattening, which can influence underlying object quality and design intent." It asks for effects at 300 dpi or more, an effect color space that matches the objects underneath, and fades that respect the printer's minimum dot.

The packaging market has already chosen. The GWG describes its 2015 release as the move "from a PDF/X-1a based world to a PDF/X-4 based world," and its packaging specs for offset, gravure, and flexo all require PDF/X-4:2010. Ask for PDF/X-4. Accept PDF/X-1a from older sources, but check flattened areas for stitched edges and spot colors converted to CMYK.

What the Ghent Workgroup flexo variant checks

The GWG 2015 packaging specification adds these checks for its flexo variant, GWG_PackagingFlexo_2015. FIRST 7 points to it as the packaging profile of PDF/X.

Check Flexo value Severity
Base standard PDF/X-4:2010, one page per file Error
Color spaces CMYK, gray, and spot only; no RGB or ICC-based color Error
White text or paths set to overprint Not allowed Error
100% black text under 12 pt, black lines under 2 pt Should overprint Warning
Rich black text Black 85% or more with total ink above 280% Warning
Smallest reversed text / text built from 2+ inks 5 pt / 14 pt (offset: 5 / 8) Warning
Thinnest reversed line / line built from 2+ inks 0.3 pt / 1.5 pt (offset: 0.15 / 0.3) Warning
Total ink coverage Above 320% averaged over a 15 mm square Warning
Continuous-tone images Error at 199 ppi or less, warning at 239 ppi or less Error / warning
1-bit images Error at 549 ppi or less, warning at 799 ppi or less Error / warning
Spot color names Near-duplicates such as "PANTONE 185 C" and "Pantone 185 CV" Warning

The flexo variant is stricter than PDF/X-4 itself on color: PDF/X-4 allows ICC-based RGB, but the GWG flexo variant does not. It also allows marked PDF/X exceptions for spot color overprints and n-channel process sets. The 2022 specs refine these rules. Ink coverage for packaging variants now counts spot colors as well as CMYK (GWG). The rich black and barcode notes cover why the text and line limits matter on press.

Dielines, white, and varnish as processing steps

Packaging PDFs carry content that must not print: the die line, crease and glue areas, white underprint, varnish, Braille, and dimension marks. ISO 19593-1 standardizes how to mark each one as a PDF layer (an optional content group) so it is excluded from printing and used only in its own processing step. PDF/X-1a has no layers, so a dieline travels as a spot color that relies on its name and an overprint setting. GWG 2022 does not make processing steps mandatory, but if a file has them, they must follow the ISO standard. For packaging it also defines product types that say which steps are required, advised, or not allowed.

What to record at file intake

Log the file check on the job, not just in the preflight log: the PDF/X part and conformance claimed, the output intent profile, the GWG variant and preflight result, the spot and technical inks found, the processing steps present, who flattened transparency, and the artwork revision approved. When a file fails before imaging, the fix costs a message to the customer. When it fails after plates are made, the record shows which file was supplied and how much plate area the remake adds. File checks belong with automated preflight and proof approval in the same job record.

Common questions

What is PDF/X?

PDF/X is a family of ISO 15930 standards that restricts PDF for print exchange. Every PDF/X file embeds its fonts and images, names the intended print condition with an ICC output intent, and excludes features such as passwords, JavaScript, and transfer curves that could make output unpredictable. The main versions are PDF/X-1a, PDF/X-3, PDF/X-4, PDF/X-5, and PDF/X-6.

Should I use PDF/X-1a or PDF/X-4 for flexo packaging?

Use PDF/X-4 unless your prepress provider asks otherwise. PDF/X-4 keeps transparency and layers live, so the prepress RIP flattens effects with settings that match the press, and the Ghent Workgroup packaging specifications for flexo are built on PDF/X-4:2010. PDF/X-1a flattens transparency at export in the design application and cannot carry layers for dielines or white.

Can a PDF/X-4 file for flexo contain RGB images?

The PDF/X-4 standard allows ICC-based RGB when the file has an output intent, but the Ghent Workgroup 2015 flexo packaging variant does not. It accepts only CMYK, grayscale, and spot colors, so convert RGB images to the press condition or agree on the conversion with your prepress provider before supplying the file.

Is PDF/X-6 ready for packaging?

PDF/X-6 was published as ISO 15930-9 in 2020 and is based on PDF 2.0, adding page-level output intents and CxF/X-4 spot color data. The Ghent Workgroup left it out of its 2022 specifications because hardware and software in the market were not ready, so PDF/X-4 remains the working standard for packaging files.

Built for flexo trade shops

Keep production context with the job.

See how Flexoworks connects customers, prepress, plate production, delivery, and plate-area billing.