Field note · Flexo prepress

ICC profiles in flexo: press profiles, rendering intents, and DeviceLinks

What an ICC profile is and what it contains, which rendering intent to use, when a standard CRPC profile such as GRACoL 2013 fits a flexo press, how FIRST builds a press profile from fingerprint and characterization runs, why CMYK-to-CMYK conversions need DeviceLinks, and what profile data belongs on the job record.

Plate area · jobs · customers · AR — one system of record
Flexoworks
  • flexo
  • color
  • prepress
  • packaging
  • color management

An ICC profile is a data file that describes the colors one device reproduces, so color software can convert a file from one device to another. In flexo, the "device" is not just a press. It is one print condition: that press, with that anilox, ink set, plates, screening, curves, and substrate. A profile built on white BOPP says little about the same press on kraft paper. The wrong profile, the wrong rendering intent, or a profile the press has drifted away from can put color off target before a single plate is imaged.

What is inside an ICC profile

Every profile translates between device values (CMYK percentages, RGB numbers) and a shared, device-independent color space. The International Color Consortium calls it the profile connection space (PCS). It is based on CIE colorimetry under D50 light, measured per ISO 13655 and viewed per ISO 3664. Because every profile points at the same PCS, any source profile can be paired with any destination profile at conversion time.

The ICC defines input, display, and output profile classes. A flexo press profile is an output profile. It holds tables for each direction (device to PCS and PCS to device) and for each rendering intent. The PCS-to-device table also fixes how the profile separates color: total ink limit, black generation (GCR), and maximum black. The Idealliance profile GRACoL2013_CRPC6.icc, for example, is built with a 320% total ink limit, medium-plus GCR, 100% maximum black, and a tone value increase of 16% for CMY and 19.1% for black. Those settings travel into every file converted with it.

Rendering intents and when to use each

A rendering intent decides what happens to colors the destination cannot print. The ICC defines four:

Intent What it does Typical flexo use
Perceptual Compresses the whole gamut to keep color relationships and detail RGB photos and images converted to press CMYK
Relative colorimetric Maps paper white to paper white; reproduces in-gamut colors exactly and clips the rest CMYK-to-CMYK conversions between similar conditions
Absolute colorimetric Leaves in-gamut colors unchanged, including the substrate color Contract proofs that simulate the press substrate; spot color targets
Saturation Keeps colors vivid at the expense of hue accuracy Charts and business graphics; rarely right for packaging

The ICC notes that perceptual and saturation mapping are vendor-specific, so two profiling tools can give different results from the same measurements. When proofing, Esko's Imaging Engine guide reminds operators that the press profile is the source and the proofer profile is the destination.

Standard profile or press profile

ISO/PAS 15339-2 and CGATS 21-2 define seven Characterized Reference Printing Conditions (APTech), from CRPC1 (newsprint) to CRPC7 (extra-large gamut). CRPC6, premium coated, is the GRACoL 2013 condition, and its profile is published for any CMYK process, flexo included. The FTA's FIRST 7 design guide says a CRPC can be the basis of the contract proof only if the press has been synchronized to it. Otherwise the printer needs a custom proofing condition.

Substrate matters even when the press is synchronized. In an FTA print project, CRPC6 assumes a paper white of Lab* 94, 1, −4, while the BOPP film on press measured 93, −0.77, 0.17, so the team built a substrate-corrected aim before profiling.

A printer's own profile is not automatically better. An FTA article on profiling for packaging prepress warns that existing press profiles may be outdated by changes in inks, substrate suppliers, plate brands, or season, or averaged across many presses, "good for all the presses but not good enough for any press in particular."

How a flexo press profile is built

FIRST works in a fixed order: optimize, fingerprint, then characterize. An open flexo calibration checklist lays out the steps:

  1. Optimize the press. Settle the anilox and inks, start from standard hue angles and solid densities, and run normal tone value increase with no slur on any unit.
  2. Image test plates with your current dot gain curves and measure tone values on the plates.
  3. Run the fingerprint at normal speed on regular stock, with a characterization chart such as the IT8.7/5. Idealliance's IT8.7/5 keeps the 1,617-patch layout of the IT8.7/4 but adds 29 gray patches for better neutrals.
  4. Calculate plate curves that move the press to the aim, and combine them with the existing compensation curves.
  5. Run the characterization with the new curves, average several sheets (the FTA project measured 10), and build the ICC profile from that data.

Add the job's spot colors and test images to the layout. CMYK plus spot or extended color gamut work needs multicolor charts and software that can profile them. The order matters in flexo: the profile describes the press after its curves, so changing the dot gain curve or the minimum dot afterward means the profile no longer describes the press.

Converting an existing CMYK file through two ICC profiles reseparates every color with the destination profile's black generation. Kodak's DeviceLink documentation warns that with full reseparation, solid colors in the original "may not remain solid." A DeviceLink converts CMYK directly to CMYK under rules. Its "fully constrained" method keeps colors made of one or two inks free of other inks and leaves solid primaries and secondaries solid. Black-purity options keep black-only text and rich black builds intact, which protects small type and barcodes. DeviceLinks also carry the total ink limit, black start, and maximum black for the target press.

Checks before a profile touches a job

  • The profile names one print condition: press, anilox, ink set, substrate, plates, screening, and curve set.
  • Its ink limit and black settings match the printer's spec.
  • The rendering intent is set per content type, not left at a default.
  • Spot colors stay spot unless the customer approved a conversion to process.
  • The proof simulates the same profile, and the proof label names it.
  • Results are measured in Delta E against the profile's aim, not judged by eye.

What to keep on the job record

Record the color setup for each job: source profile, destination press profile and version, rendering intent, any DeviceLink, the curve set, and the date of the characterization run behind it. When the press, substrate, anilox, or ink changes, the record shows which open jobs used the old profile. When a customer disputes color, it shows the condition the proof simulated. When a reprofile forces new plates, it shows the remake and the plate area it adds.

Common questions

What is an ICC profile?

An ICC profile is a standard data file that describes how a device reproduces color, by mapping its device values (such as CMYK percentages) to a device-independent color space defined by the International Color Consortium. Color management software pairs a source profile with a destination profile to convert a file from one device to another. In flexo, a press profile describes one print condition: press, anilox, ink, plates, screening, curves, and substrate.

Which ICC profile should I use for flexo printing?

Use the profile for the exact press and substrate the job will print on. If the printer has synchronized the press to a standard condition, such as CRPC6 (GRACoL 2013), that published profile can be the reference for files and contract proofs. If not, the printer needs a custom profile built from a fingerprint and characterization run. Ask the printer or prepress provider before converting files.

What is the difference between relative and absolute colorimetric?

Both reproduce in-gamut colors exactly and clip colors the destination cannot print. Relative colorimetric maps the source paper white to the destination paper white, so the substrate color is not simulated. Absolute colorimetric keeps all in-gamut colors unchanged, including the substrate color, which is why it is used for contract proofs that simulate the press substrate.

How often should a flexo press profile be updated?

Whenever the print condition it describes changes: a new substrate, ink supplier, anilox, plate type, screening, or curve set. Esko notes that a new substrate needs a new profile, and the FTA warns that profiles drift out of date with ink, substrate, and plate changes, and with the seasons in plants without climate control. Verify the press against the profile with a measured control strip before trusting it.

Built for flexo trade shops

Keep production context with the job.

See how Flexoworks connects customers, prepress, plate production, delivery, and plate-area billing.