Field note · Flexo prepress

Registration marks in flexo: targets, microdots, and eye marks

What registration marks do in flexo printing, how crosshair targets, microdots, and eye marks differ, how to use registration color, typical print-to-print and print-to-cut tolerances, and what belongs on the job record.

Plate area · jobs · customers · AR — one system of record
Flexoworks
  • flexo
  • registration
  • plate mounting
  • prepress
  • packaging
  • labels

Registration marks are small targets printed outside the finished design so every color station lines up with the others. On a flexo job they do more than that. Crosshair targets and microdots guide plate mounting, press marks feed automatic register control, and eye marks tell a bag machine or sheeter where to cut. Which marks a job needs, where they sit, and how tight the register has to be are all part of the job spec.

The marks on a flexo job

Mark What reads it Typical spec Where it goes
Crosshair target Mounting operator and press crew About a 1/4 in circle with crosshairs Center of each side, outside the print
Microdot Camera plate mounter 0.005 to 0.016 in dot Web edges, sometimes inside the image
Eye mark Photo-eye on a bag machine, form-fill-seal line, or sheeter Often 10 x 5 mm solid black A clear lane along the web, once per repeat
Control targets Press operator and QC Color-to-color and print-to-cut elements Flaps, glue zones, or waste matrix

The target and microdot sizes come from a camera-mounting patent that describes both systems. The eye mark size is the standard in Harkwell's artwork guide, which also says to confirm it with the converter. The FTA's FIRST design guide lists color-to-color and print-to-cut registration as one of five test elements that should be on every process design.

Crosshairs vs microdots

Crosshair targets are easy to see, so they sit outside the live image. That makes each plate larger than the print needs and limits how closely plates can be ganged on a cylinder. Microdots are small enough to hide, so plates can be smaller. They need a camera mounter, because the eye cannot align a 0.010 in dot.

Converters often prescribe one system. Garlock's flexible packaging spec requires microdots and asks designers not to add crosshairs or BST marks. It adds at least two 0.016 in dots at the web edges, plus one at the center on jobs wider than 30 in. Sealed Air's Autobag guide uses 0.009 in squares on each color and warns that they are usually trimmed off but sometimes end up on the finished bag.

Registration color

Registration marks use the Registration swatch. In Adobe Illustrator, anything in Registration prints on every separation, including spot-color plates, as an equal tint of all inks. That is why one target works for every station.

It is also why Registration must never be used in the artwork. Type or a box filled with it prints on every plate and lands muddy on press. ePac's artwork spec says it plainly: do not use the Registration swatch for anything. Preflight should flag live art in Registration and check that marks reach the white and varnish plates too.

Registration tolerances

Source Print-to-print Print-to-cut
ViaFlex, labels ±0.010 in (1.5 dots at 150 lpi) ±1/32 in
ViaFlex, underside of multi-layer labels ±0.020 in ±1/16 in
Sealed Air Autobag, bags ±1/64 in process, ±1/32 in line Not stated
FIRST 4.0, total trap tolerance 1/64 in for preprint linerboard; 1/16 in between stations and 1/8 in through the press on combined corrugated Confirm with the printer

The corrugated figures come from the FIRST 4.0 design guide. Tolerance drives design rules. FIRST says type in different colors should sit more than twice the trap apart, and a holding line around multi-color reverse type should be twice the registration tolerance. The trapping note covers how trap width follows from it.

Where the marks go

FIRST suggests placing control targets under flaps, in a glue zone, or on the waste matrix, and asks the designer to mark that area on the template. Farnell Packaging adds eye marks, microdots, and registration marks in prepress and shows them on the proof. If the design has no room, extra trim may be needed, at extra cost. Eye mark lanes should stay free of text and graphics, so the photo-eye sees one clean mark per repeat.

Reading the marks when register is off

The marks help sort the cause. If the targets line up but one element is off, the problem is in the file, such as a missing trap or an object on the wrong separation. If the targets are doubled, a plate was mounted off or the press is out of register. If the error grows around the repeat, check that every plate was output with the same distortion factor.

What to keep on the job record

Record which marks each customer and press want (crosshairs, microdots, eye marks, press marks), their size, color, and position, the eye mark lane and repeat pitch, the agreed print-to-print and print-to-cut tolerances, who adds the marks, and the mounting file revision. Mark positions also affect the step-and-repeat and the trim, which change plate area. A rerun that pulls the same record gets the same marks, the same mounting setup, and the same cut position against the dieline.

Common questions

What are registration marks in printing?

Registration marks are small targets, usually a circle with crosshairs, printed outside the finished design in Registration color so they appear on every separation. Press and mounting operators line them up so each color prints in the right place. In flexo, microdots and eye marks do similar jobs for camera mounters and converting equipment.

What is the difference between crop marks and registration marks?

Crop marks show where the printed piece is trimmed. Registration marks show whether the color separations line up with each other. On die-cut flexo labels and cartons, the dieline replaces crop marks, while registration targets, microdots, and eye marks stay in the waste or trim area.

What is registration color?

Registration color is a built-in swatch that prints on every separation, including spot-color plates, as an equal tint of all inks. It is meant only for registration marks and other printer's marks. Using it for type or artwork makes that element print on every plate and look muddy on press.

What are microdots in flexo printing?

Microdots are tiny registration dots, roughly 0.005 to 0.016 inch, imaged on each plate in place of crosshair targets. A camera plate mounter aligns them so every color mounts in register. Some converters, such as Garlock, require microdots at the web edges and ask designers not to add crosshairs.

Built for flexo trade shops

Keep production context with the job.

See how Flexoworks connects customers, prepress, plate production, delivery, and plate-area billing.