Field note · Flexo prepress

AM, FM, and hybrid screening in flexo

How AM, FM (stochastic), and hybrid screening differ in flexo, why pure FM is rare, how hybrid screens fade highlights, and which screening data belongs on the job record.

Plate area · jobs · customers · AR — one system of record
Flexoworks
  • flexo
  • screening
  • stochastic-screening
  • hybrid-screening
  • halftone
  • prepress

AM screening builds tone by changing the size of halftone dots on a fixed grid. FM, or stochastic, screening keeps one small dot size and changes how many dots are placed, in a pseudo-random pattern. Most flexo process work runs AM dots through the midtones and switches to FM-style dots in the highlights, which is called hybrid or transitional screening. The screen, ruling, angle set, and minimum dot a customer approved are part of the print condition, so they belong on the job record.

AM, FM, and hybrid at a glance

Screen How it makes tone Strength in flexo Risk in flexo
AM (conventional) Dot size changes on a fixed ruling and angle Stable midtones and predictable curves A hard break where highlight dots stop; moiré with the anilox or between colors
FM (stochastic) Dot size stays fixed; the number of dots changes No rosette or screen-angle moiré Every dot is highlight-sized, so gain and dot holding are hard to control
Hybrid (AM/FM) AM in the midtones; fixed-size dots removed at random in the highlights Fades toward 0% while holding the plate's minimum dot Grain in the FM zone and a visible kink if the switch is abrupt

Why pure FM is rare in flexo

Stochastic screening places same-size dots in a pseudo-random pattern, so there is no screen angle and no rosette. In flexo, that dot is about the size of a conventional highlight dot, and highlights are where flexo gains most. Flexopedia's screening guide advises using stochastic screens only after the printer and separator have run press fingerprints to set the dot size and gain compensation.

The gain is large. Kodak's Prinergy flexo screening training notes that a 2% screen in the file can measure 8% or more on the press sheet. A pure FM image is built entirely from dots of that kind.

Why AM alone breaks in the highlights

Every plate has a minimum printable dot. Below it, AM dots either drop out or are bumped up to the minimum, so a vignette that should fade to white ends in a hard edge. Kodak calls this flexo discontinuity and notes that a higher screen ruling increases highlight gain and makes the break larger.

How hybrid screening fixes the fade

A hybrid screen keeps the AM grid where it prints well. Once dots reach the plate's minimum size, the screen stops shrinking them and removes them instead, so tone keeps falling while every remaining dot can still hold on the plate.

  • Kodak's Maxtone CX removes minimum-size dots from the AM grid. Maxtone FX and SX switch to true FM, and SX uses a longer transition that Kodak recommends as the first choice.
  • Esko's HD Flexo application guide covers 120 lpi and above, requires true 4000 ppi imaging, and sets screens so a 0.38% grey level still makes printable dots.

The transition point moves with ruling. In a Flexo 24 example on a 1.14 mm plate with a 50 micron minimum dot, the hybrid zone ended near 7% at 149 lpi and near 2.4% at 87 lpi.

The trade-off is grain. Kodak warns that removed dots can look grainy, especially with larger minimum dots, and that a fast AM-to-FM switch can show a kink because the two zones gain differently.

Angles still matter for the AM part

Engraved anilox cells add a pattern that offset does not have, so flexo avoids offset angles. Kodak's screen angle guidance gives a typical shifted set of C 67.5°, M 7.5°, Y 82.5°, K 37.5°. ISO 12647-6, as summarized by flexo•expert, keeps cyan, magenta, and black 30° apart, yellow 15° from another color, and no color aligned with the anilox engraving. The ruling still has to suit the roll; see anilox line screen selection.

What to keep on the job record

For each approved print condition, record the screen family and name, ruling, angle set, dot shape, minimum dot in pixels or microns, transition point, imaging resolution, plate type, anilox LPI and BCM, and the curve built from the fingerprint. When a rerun moves to a different plate or imager, these settings decide whether highlights and fades match. Keep them with the dot gain curve and the plate QC record, and compare RIP options in the screening software note.

Common questions

What is the difference between AM and FM screening?

AM (amplitude modulated) screening changes the size of halftone dots on a fixed grid with a set ruling and angle. FM (frequency modulated), or stochastic, screening keeps the dot size fixed and changes how many dots are placed, in a pseudo-random pattern, so it has no screen angles or rosettes.

Is stochastic screening used in flexo printing?

Pure stochastic screening is uncommon in flexo because every FM dot is about the size of a highlight dot, where flexo gains most. Flexo shops usually use hybrid screens instead: AM in the midtones and FM-style dots of the plate's minimum size in the highlights. Pure FM should only follow a press fingerprint.

What is hybrid screening in flexo?

Hybrid, or transitional, screening uses AM dots through most of the tonal range. When dots reach the plate's minimum printable size, it removes dots instead of shrinking them, so vignettes fade toward 0% without a hard edge. Examples include Kodak Maxtone CX, FX, and SX and Esko HD Flexo screens.

What screen angles are used in flexo?

Flexo usually uses angle sets shifted by 7.5 degrees to avoid moiré with the anilox engraving. A typical set from Kodak is cyan 67.5, magenta 7.5, yellow 82.5, and black 37.5 degrees, with cyan, magenta, and black 30 degrees apart.

Built for flexo trade shops

Keep production context with the job.

See how Flexoworks connects customers, prepress, plate production, delivery, and plate-area billing.