A densitometer measures how much light a print, film, or mask absorbs and reports it as optical density. In a flexo pressroom it is the fastest way to watch solid ink density, dot gain, and trap during a run. It does not measure color, and it is the wrong tool for reading dots on a photopolymer plate. Knowing where it fits saves arguments between the plate room and the press.
How a densitometer works
Density is a log scale: D = log₁₀(1/R), where R is the share of light reflected (or transmitted, for film). X-Rite's densitometry guide gives the scale: 100% reflectance is 0.0 D, 10% is 1.0 D, 1% is 2.0 D, and 0.1% is 3.0 D. Each step of 1.0 D means ten times less light.
- Reflection densitometers read ink on a substrate: solids, tints, and overprints in the control strip.
- Transmission densitometers read light passing through film negatives and laser-ablated masks.
- Spectrodensitometers report both density and L*a*b* from one spectral reading.
Color filters let the instrument read each process ink through its complementary color. The filter response is called a status, defined in ISO 5-3. Status T is the US standard and Status E the European one. Yellow is where they differ most: X-Rite's European table lists a high-gloss yellow at 1.40 in Status E and 1.00 in Status T. A density number without its status is not comparable.
What it measures on press
| Measurement | Formula | What it tells the operator |
|---|---|---|
| Solid ink density | log₁₀(1/R) on a 100% patch | Ink film thickness or ink strength |
| Apparent dot area (tone value) | Murray-Davies: (1 − 10^−(Dt−Dp)) ÷ (1 − 10^−(Ds−Dp)) | Printed dot size, including optical gain |
| Tone value increase (dot gain) | Printed dot area − file value | Impression, plate, tape, and anilox effects |
| Apparent trap | Preucil: (Dop − D1) ÷ D2 | How well one ink prints over another |
| Print contrast | (Ds − Dt) ÷ Ds, at 75% | Whether shadows stay open |
Dt is the tint, Ds the solid, Dp the substrate, and Dop the overprint. Formulas are from X-Rite's guide.
A worked example. Cyan solid reads 1.40, the substrate 0.10, and the 50% patch 0.60. Murray-Davies gives 72% apparent dot area, so dot gain is 22%. If the operator takes the solid from a different spot that reads 1.25, the same tint calculates as 74%, two points of gain with nothing changed on press. Switch to the Yule-Nielsen formula with an n-factor of 2 and the same readings give 56%. The formula and the solid reference have to be written down with the result. Our dot gain note covers how those readings become plate curves.
Why flexo density drifts differently
On offset, density tracks ink film thickness. On flexo, X-Rite notes that density also tracks ink strength: adding water or extender lowers it, and solvent evaporation during the run raises it. A density drift on a flexo press can be an ink viscosity or pH problem, not a plate or anilox problem. The same source puts good trap at 80% or better and says it is easier on presses with dryers between stations, as many flexo presses have.
Density also cannot confirm color. A cyan and a magenta can both read 1.25. A contaminated ink can hit its density and still look wrong. Standard CMY filters give unstable readings on spot inks, so spot colors need a spectral density at the ink's peak wavelength and spot color tone value (ISO 20654) for tints. The FTA's FIRST 6.0 lists densities only as starting points for paper, film, and newsprint, and sets presses up on L*C*h targets. Match color with a spectrophotometer and Delta E, then use density to hold it through the run.
Fix the settings before comparing numbers across shifts or sites: status, backing, polarization, absolute or relative density, dot area formula, and trap formula. On clear film, ISO 13655 calls for a white backing, and a printed opaque white does the same job.
Densitometers in the plate room
Transmission density still matters for film and masks. ISO 12647-6 asks for film with a core density of 4.0 or above, clear film no higher than 0.15, and clear dot centers no more than 0.1 above clear film. For digital plates, the FTA describes checking the mask's stain density and a 50% patch after imaging.
The finished plate is different. Image and non-image areas on a photopolymer plate have little contrast, so X-Rite says a reflection densitometer needs a Yule-Nielsen n-factor set for each plate type and dot range. Camera-based plate readers photograph the dots and calculate area from their edges instead. The BetaFlex Pro2 and FLEX4PRO also report dot diameter, edge factor, and mask stain density. FAG lists 0.2% to 99% dot range and ±0.2% repeatability for the FLEX4PRO.
ISO 12647-6:2020 asks each plate to carry compensated and uncompensated patches at the minimum dot, 10%, 30%, 50%, 70%, and solid. It allows ±1 at 10% and below and ±2 above for rulings up to 48 lines/cm (about 122 lpi), and ±2 and ±3 for finer rulings. It also says there is no standard method for measuring dots on a plate, so the shop and its customer must agree on the device. The FTA's minimum is two-point control: a midtone and a highlight measured on every plate, or a sample of plates. Our plate QC checklist and minimum dot note cover what to do with those readings.
What to keep on the job record
Record the instrument and its last certification date, the status, backing, polarization or measurement mode, absolute or relative density, the dot area formula (and n-factor if used), and the trap formula. Add the solid and tint readings from the approved press OK, the plate reader values for each plate's control patches, the mask stain density, and who measured. When a converter says a plate printed heavy, that record shows whether the plate, the ink, or the measurement changed, before anyone pays for a remake.
Common questions
What is a densitometer used for in printing?
A densitometer measures optical density, how much light a printed ink, film, or mask absorbs. On press it is used to monitor solid ink density, dot area and dot gain (tone value increase), trap, and print contrast during a run. In the plate room, a transmission densitometer checks film density and the stain density of laser-ablated masks.
What is the difference between a densitometer and a spectrophotometer?
A densitometer measures how light or dark an ink prints, not its color. Two different inks can have the same density, and a contaminated ink can hit its density target and still look wrong. A spectrophotometer measures the full spectrum and reports L*a*b* color, so it is used to match color and calculate Delta E. Many shops match color with a spectrophotometer, then hold it through the run with density.
Can a densitometer measure flexo plates?
Not reliably. Photopolymer plates have little contrast between image and non-image areas, so a reflection densitometer needs a Yule-Nielsen n-factor set for each plate type and dot range. Camera-based plate readers photograph the dots and calculate dot area from their edges, and also report dot diameter and edge factor. ISO 12647-6 says there is no standard method for measuring dots on a plate, so the device should be agreed between the trade shop and the printer.
What is a good solid ink density for flexo printing?
There is no single number. It depends on the substrate, ink, anilox, and press. The FTA's FIRST lists densities only as starting points for paper, film, and newsprint, and recommends setting the press up on colorimetric (L*C*h) targets. Once a fingerprint is approved, the solid densities from that run become the production targets, measured with the same status, backing, and settings.